 |
||||||||||
|
||||||||||
| Project Name | Supplies |
| Antique Lace Bobbins
|
Tools: Lathe with assorted chisels, shop-made drive center, dividers, small half-round and rat tail file, mini-drill and bit, and needle nose pliers. Supplies: 1/2” x 1/2” x 5” maple, brass wire, assorted beads and buttons, nylon fishing line, assorted grits of abrasive paper, friction polish or finish of choice. |
 |
|
| Faux Ornamental Turned Box |
Tools: Lathe with assorted chisels, index wheel, router with carriage, 1/4” and 1/2” cove bits, router sled, drill chuck and 3/8” Forstner bit. Supplies: 3” square x 6” long ash for box 3/4” x 2-1/2” square purpleheart for lid 5/8” square x 2” ash for knob 3/8” diameter x 1/4” purpleheart for plug Assorted grits of abrasive paper Finish of choice Buffing wheel |
|
|
| Shopmade Outboard Tool Rest Stand | Tools: 2 pipe wrenches, drill, taps, metal cutting saw, this can be as simple as a hack saw or, if available, a metal cutting bandsaw which will make cutting much easier. Supplies: 1” ID galvanized water pipe in the following lengths: 2 pieces - 2’ long, threaded on both ends 1 piece – 3’ long, threaded on both ends 1 – 1” galvanized water pipe “T” 1 – 1” galvanized water pipe flange 1-1/4” galvanized water pipe in the following lengths: 2 pieces – 2’ long, threaded on both ends 1 – 1-1/4” galvanized water pipe 90° elbow 1 piece of 1/2” thick steel plate, 8” square 4 – Knobs with threaded studs 2 – Lag bolts or bolts and nuts, depending on lathe attachment. Flat head machine bolts and nuts |
|
|
| Shop-Built Bottle Stopper Chuck |
Tools: Lathe, bandsaw, 6”or 8” bench grinder, scroll chuck with spigot jaws or drill chuck with appropriately sized Morse taper, “V”-sized (0.3770) twist drill bit, cross cut sled with adjustable stop, pen blank drilling jig, and wooden mallet. Materials: 4” length of 3/8” diameter steel rod assorted grits of abrasive paper Steel wool Magic marker Thick Cyanoacrylate glue (CA or super glue) Q-tip Renaissance wax or finish of choice |
|
|
| Spiral Wire Ornament | Wire for Globe: (www.McMaster.com, 1/4 lb, #8870K13 @ $2.62 and #8904K71 @ $6.77 as of 5/23/07). Tools & Materials: Wire Turning Square, 1” x 1” x 6-3/4” Spindle roughing gouge, detail gouge, parting tool, 1/2” skew, mini-cove tool, narrow parting tool, pin chuck, spiraling hook, 180 and 320 grit abrasive, and 3M 7448 non-woven pad |
|
|
| Table Coaster | Tools: Lathe with screw center faceplate, re-ground square nose scraper, small spindle gouge, ruler straight edge, spear point chisel (optional) and a 1/2” skew. Materials: Wood: 7/8” X 6-1/2” diameter, walnut Cork: 1/8” X 2-3/4” diameter Bees wax Glue Finish of choice |
|
|
| Segmented Christmas Ornament | Ornament Supplies: holly, 3/4" x 2" x 5" (longer ok) purpleheart Veneer cherry, 3/4" x 3/4" x 6" Small eyelet MDF 3/4" x 2" x 5" (longer ok) Cyanoacrylate glue Yellow glue Tool Making Supplies: (3) 10" length of 1/2" metal rod (3) 1/8" Allen wrench (3) 8-32 set screw 8-32 tap Clothes hanger Tools Needed: 3 hollowing tools (The ones we just made) Skew Bowl gouge |
|
|
| Segmented Pen | Supplies Needed: Wood of choice Pen kit of your choice either from Arizona Silhouette or Craft Supply USA. Sanding material of choice Finish of choice. I use EEE Cream & Behlen’s Woodturners Finish Abralon Sanding pads Urethane Glue & spring clamps 4” wide masking tape or packaging tape Medium and thin cyanoacrylate glue (CA or Superglue) Tools Needed: Planer, table saw, spring clamps, ruler, drill press with appropriate drill bit, drill centering jig, pen mandrel with appropriate bushings, disc sander, and a lathe with skew chisel or small gouge. |
|
|
|
|
©2008, 2007, 2006, 2005, 2004 All American Crafts
Reproduction of the contents of this website or magazine (including images) in any way whatsoever without written permission of the Publisher is strictly prohibited.
ANY unauthorized use of the materials contained within WILL be prosecuted to the fullest extent of the law.
Woodturning Design Magazine is published by All American Crafts, Inc. View our other magazines.