| Project Name |
Supplies |
Dual Turning
page 16 |
Wood:
White oak — one piece 1” X 2-1/2” X 9-1/2” for base
Black walnut — one piece 3/4” X 2” X 4” for lids
White oak and black walnut — 3/4” X 3/4” X 6” for finial sections
Tools:
Thickness planer, square,
ruler,
lathe with adjustable chuck,
table saw or
chop saw,
parting tool,
3/8” bowl gouge
Waste block
Plywood
Short screws
Foam pads
Assorted grits of abrasive paper
Glue of choice
Finish of choice |
 |
Making Antler Pens
page 22 |
Antler
(such as Sambor, Axis, Rusa, and Whitetail deer)*
Tools:
Lathe,
drill press with centering device and appropriate-sized drill bit,
pen
insertion tool,
bandsaw or scroll saw,
barrel trimmer,
roughing gouge,
skew,
compressed air
Pen kit of choice**
Thin and medium-viscosity cyanoacrylate glue (CA or superglue)
Assorted grits of abrasive paper
Abranet sanding material (optional)
Abralon Pen Finishing Kit***
Triple EEE Cream***, Behlen’s Woodturner’s Finish***, or finish of choice
Dust mask (important!)
Paper towel
*Available from Penn State Industries, 9900 Global Road, Philadelphia, PA
19115; phone: 800-377-7297; Website
** Available from Berea Hardwoods (877-736-5487),
Craft Supplies (800-551-8876,
Packard Woodworks (800-683-8876),
or Penn State Industries (800-377-7297.
*** Available from BG Artforms, 2189 Philip Drive, Bensalem, PA 19020;
phone: 888-717-4202 (toll free); website; Order:
Abralon Pen Finishing Kit (PFK-2) $12.95, Triple EEE Cream $16.75,
Behlen’s Woodturner’s Finish $16.75, Hot Stuff “Super T” cyanoacrylate
glue (HST-4) 2 oz. Bottle $9,95, River Buffalo Horn $9.50 per blank.
|
|
Adapt-A-Sled
page 28 |
Wood:
Scrap piece of wood or sheet goods of some kind
(plywood, medium-density
fiberboard, particle board)
Tools:
Table saw,
stop block,
table saw sled (or make your own),
miter gauge,
clamps
Sheet of self-stick foam (available from any craft department
Fine abrasive paper
Scissors
Pencil |
|
| Spiral-Fluted Vase
page 54 |
Wood:
11” to 14” long whole log about 6” to 7” in diameter (grapefruit wood
was used for vase featured.)
Tools:
Spur drive, live center,
3” or 4” faceplate,
steady rest,
boring bar and
cutters,
variable speed drill,
drive socket,
5/32” drill bit,
3/8” rounded and
3/8"
sharply beveled gouges,
3/4” continental gouge,
outside calipers and
thickness calipers,
flexible straight edge,
small round cutter in Stewart tool
Screws to attach faceplate (1-1/2” long X 1/4” shank hex head concrete screws were used for project featured)
Pencil
To make your own depth gauge (optional:
1/4” thick X 1-1/2” wide X 16” to 20” long flat piece of wood,
3/8” dowel about 12” to 15” long,
heavy black thread,
cyanoacrylate glue (CA or superglue) |
|
Caragana Weed Pot
page 62 |
Wood:
1-1/4” X 3” limb section (Caragana/Siberian pea tree was used for project
featured)
Tools:
Drill press,
1/4” drill bit,
lathe,
cone center,
spur drive,
3/8” and 3/4” gouge,
1/2” skew chisel,
1/8” parting tool, tapered reamer (optional)
Block of beeswax
Assorted grit of abrasive paper
Sharp knife
Paper towel or sacking |
|
Wooden Chuck Jaws
page 71 |
Wood:
Species of choice (big leaf maple was used for project featured)—one piece
2” X 5-3/8” X 38” or 2” X 6-1/2” X 42” depending on chuck*
Tools:
Table saw,
bandsaw,
compass,
combination square,
lathe with chuck,
bowl
gouge,
parting tool,
screws
Double stick tape
*Mega-jumbo jaws and Stronghold chucks are available from Oneway
Manufacturing, 241 Monteith Ave, Stratford, ON, Canada N5A 2P6;
Phone 800-565-7288; website
Cole jaws for Nova chucks are available from Craft Supplies USA, 1287
E. 1120 S., Provo, UT 84606; phone: 800-551-8876; website |
|
Raku Pot
page 74 |
Bowl blank of choice (cherry or wood of choice)
Tools:
Lathe,
Forstner bit to fit spur center,
live center,
Sorby 1/2” bowl gouge* with fingernail grind,
faceplate,
1-1/8” and 3/4” Forstner bits with
diamond hone,
boring bar with laser thickness gauge and hollowing rig**,
large live center***,
1/4” round skew,
parting tool,
large round scraper or Rolly Munro cutter,
3/16” square cutter,
electric drill,
Jacobs chuck,
wood chisel and mallet
Eight large wood screws
Cyanoacrylate glue (CA or superglue) with accelerator
Hot melt glue
Power sanding equipment with assorted abrasive discs
Sanding sealer
Airbrush
Aniline dyes (black, yellow, red, green, and turquoise or colors of choice)
Compressed air
Respirator and vacuum system
Face shield
Test board (scrap wood)
Pencil
Newspapers
Latex gloves
Plastic bag
Cotton swabs
*Available from Woodcraft, P.O. Box 1686, Parkersburg, WV 26102;
phone: 800-225-1153; website Order: No.
126944.
**Available from Keith Clark, 300 NW 18th, Oklahoma City, OK 73103;
phone: 405-528-5476; website: email or by cell phone at 405-823-1518.
***Available from Oneway Manufacturing, 241 Monteith Ave, Stratford,
ON, Canada N5A 2P6; phone: 800-565-7288; website |
|
|
