TRIPLE CAPTIVE RING PEN

Carl Knoll

MATERIALS NEEDED:
Pen kit of choice (Woodcraft, European Style used here)
Wood blank ¾” X ¾” X 5” – African Blackwood
Mylands High Build Friction Polish or finish of choice
Hot Stuff, Super T medium cyanoacrylate glue(CA or superglue)
Assorted grits of abrasive paper--120 to 500 grit
Micro-Mesh Soft Touch Pads--grades 1500 - 12000
Soft cloths
Q-tips type applicators
Masking tape

TOOLS NEEDED:
Lathe with assorted standard turning tools; skew, roughing gouge, parting tool;
Pin drill and custom right angle turning tool blade;
Modified Black & Decker NaviGator metal saw blade (#74-593);
Xacto blade (modified X104 blade) and handle of choice;
Dremel rotary tool,
small diamond carving bits
buffing wheel (Dremel 401 polishing wheel).
6” caliper (or smaller)

Please refer to all manufacturers' labels for proper product usage.

CHRISTMAS ORNAMENTS, PART 1

Johnny Tolly

TOOLS NEEDED:
Lathe with assorted chisels
StebCenter drive
4-jawed chuck with #1 jaws, or equivalent
Shop-made "story stick"
Shop-made tenon gauge
Pin vise with small drill bit

MATERIALS NEEDED:
Eye screws P/N, 7416 Pkg 20 ea $4.00 Pkg 100 ea $14.50, as of this writing.*
Sanding supplies **
Maple ball blanks***
Burl Mesquite from Unique Mesquite****

Spray Lacquer by Rust-Oleum

* Meisel Hardware Specialties
1-800-441-9870 | www.meiselwoodhobby.com

**www.turningwood.com orwww.turningwood.co

*** www.gonebatty.net

****Unique Mesquite Custom Woodworks
PO Box 387, 1402 Avenue M Hondo, TX 78861
866-597-6100 | www.uniquemesquite.com

Please refer to all manufacturers' labels for proper product usage.

PEANUT CANDY DISPENSER

Johnny Tolly

MATERIALS NEEDED:
Sanding supplies.
Wood glue, Q-Tips or shop rags for glue clean up.
¼” x 1" dowels
⅜” wooden button plug
Spray finish of choice
Pint, Ball, Mason or Kerr regular pint jars
Cork pads for the bottom to protect table tops
Wide mouth, pint, Ball, Mason or Kerr jars for gum ball dispensers.

TOOLS NEEDED:
Table saw with ripping and cross cut blades.
Band saw.
Drill press with ¼” and ⅜” drill bits
Lathe with assorted chisels
Screw chuck, and OneWay Talon chuck equilivent, larger chuck for the gum ball dispenser.
Pneumatic brad nail gun with ⅝” brads
Freud Quadra Cut Router Beading and Roman Ogee Bits*
Calipers and or divider

TOOLS NEEDED:
Table saw with ripping and cross cut blades.
Band saw.
Drill press with ¼” and ⅜” drill bits
Lathe with assorted chisels
Screw chuck, and OneWay Talon chuck equilivent, larger chuck for the gum ball dispenser.
Pneumatic brad nail gun with 5/8” brads
Freud Quadra Cut Router Beading and Roman Ogee Bits*
Calipers and or dividerss

* Rockler Woodworkers Store |1-800-279-4441

Wood cut list:
These measurements are for a 36” length of wood.
7-½” dispenser for peanut dispenser 4 each
8-½” dispenser for gum balls 4 each
3-¾” body for peanut dispenser 9 each
4” body for gum balls 8 each
4-½” peanut dispenser top 7 each
5-½” peanut dispenser bottom or gum ball top 6 each
6-¼” gum ball bottom

Please refer to all manufacturers' labels for proper product usage.

INDEXING SYSTEMS

David Reed Smith

TOOLS AND MATERIALS NEEDED

Basic:
¼” plywood
Hardwood for locking slide
Drill matching spindle diameter
Bandsaw
Compass

Adjustable:
⅛” aluminum or
¼” plywood or
¼” Plexiglas
¼" x #20 round socket head screws
¼" x #20 tap
#7 drill

Please refer to all manufacturers' labels for proper product usage.